OXVA Xlim V3 Pod Cartridges

For most of the XLIM range, yes. OXVA lists this cartridge across the XLIM series, and the compatible devices section on this page shows the XLIM models we stock that appear on that list, plus the XLIM Pro 3 and XLIM 3 Ultra which we verified individually.

There is one exception. The XLIM C does not take these cartridges - it has its own XLIM C replacement pods, despite carrying the XLIM name. If your device is an XLIM C, order those instead.

If your model is not shown in either case, check the series name printed on the device before ordering rather than assuming from the name alone.

Choose by the draw you want, then set your device to OXVA's published range for that cartridge.

1.2 ohm runs at 10-12W and gives the tightest, coolest mouth-to-lung draw, closest to a cigarette. It is designed for nicotine salts. 0.8 ohm runs at 12-16W, still mouth-to-lung but a little warmer, also suited to salts. 0.6 ohm runs at 20-25W and opens the draw up into restricted direct-to-lung territory, and takes freebase or salt. 0.4 ohm runs at 26-30W, the warmest and most open of the four.

If you are coming off cigarettes and want something familiar, start at 1.2 ohm or 0.8 ohm with a nicotine salt. If you want more vapour and a looser inhale, go to 0.6 ohm and drop the nicotine strength to match.

OXVA publishes a range for each resistance: 0.6 ohm at 20-25W, and 0.8 ohm at 12-16W. The other two are 0.4 ohm at 26-30W and 1.2 ohm at 10-12W.

Start at the bottom of the range rather than the middle. A new cartridge that is fired hard before the wick has fully saturated is the most common cause of a burnt first tank, and you cannot undo it. Work up a watt or two at a time until the flavour is where you want it, and back off if it starts to taste sharp or dry.

On a device with no wattage control, the output is already matched to the cartridge and there is nothing to set.

There is no fixed figure, and any shop quoting an exact number of refills is estimating. A cartridge is finished when the flavour turns flat or slightly burnt no matter how much liquid is in it. What shortens that life is mostly how you use it: running a cartridge dry even briefly, vaping at the top of the wattage range rather than the middle, and dark or heavily sweetened flavours that gunk a coil faster than light fruit or menthol.

Keeping it topped up rather than letting it run low is the single thing that makes the most difference.

NeXLIM is a separate platform. OXVA lists the UNITECH cartridge against its NeXLIM devices and the XLIM cartridge against its XLIM devices; neither list includes the other series. If the device says NeXLIM, order a NeXLIM cartridge rather than this one.

You can, but expect some carry-over. The wick holds onto the previous flavour, so the first few draws after a switch usually taste like a blend of the two. Moving between similar flavours is fine; going from a strong menthol or dessert to a light fruit is where it is most noticeable.

Emptying the cartridge, letting it sit briefly and then filling with the new liquid reduces it. If you switch often, keeping one cartridge per flavour from the pack is simpler than fighting it.

They are two cartridge designs within the same XLIM family, offered in the same 0.4, 0.6, 0.8 and 1.2 ohm resistances. The V3 top-fill is the one listed here, filled through a silicone stopper on the top edge. OXVA also produces an EZ cartridge line alongside it.

If your device came with a top-fill cartridge, this is the direct replacement.

No. The mesh coil is built into the cartridge, so there is nothing to unscrew or replace on its own. When the flavour dulls or the coil is spent you fit a fresh cartridge, which is why these are sold in a multi-pack.