OXVA XLIM Pro 3 Pod Kit

Compatibility

Compatible replacement pods & resistances

Compatibility last checked 2026-07-31.

Verified compatibilityChecked against manufacturer data

Genuine productsAuthenticity guidance included

Secure checkout & supportEncrypted payment · UK customer support

Overview

The OXVA XLIM Pro 3 is the current top of the XLIM line. It carries a 1500mAh battery, the largest in the range, and a 1.05-inch colour screen roughly double the size of the one on the Pro 2. Output stays at 5-30W, with side airflow control and both auto-draw and button firing.

Inside is OXVA's Photon chip with its Pulse output system, which OXVA describes as delivering power in high-frequency pulses for a steadier draw. It is not a mode you switch on; it is simply how the board behaves.

It takes the same XLIM Top Fill cartridges as every other XLIM, so moving up the range does not change what you reorder. Compare the rest in OXVA XLIM pod kits.

Compare the range

Compare the OXVA XLIM Pro line

All three run 5-30W, take the same XLIM Top Fill cartridges and hold 2ml in the UK, so the choice is not about power or what you reorder. What separates them is the chipset and the screen: the Pro 2 is the straightforward version, the Pro 2 DNA swaps in an Evolv DNA board you can tune from a PC, and the Pro 3 adds a bigger battery and a far larger display.

Compare the OXVA XLIM Pro line — model comparison. Prices and availability are shown live from each product.
Attribute	OXVA XLIM Pro 2 Pod Kit £19.99	OXVA XLIM Pro 2 DNA Pod Kit £28.99	OXVA XLIM Pro 3 Pod Kit £19.16You're viewing
Battery	1300mAh built in	1300mAh built in	1500mAh built in
Display	0.56-inch colour screen	0.56-inch colour screen	1.05-inch colour screen
Chipset	Standard OXVA board	Evolv DNA, 30,000 coil reads per second, EScribe-programmable	OXVA Photon chip with Pulse output system
Charging	USB Type-C, 5V/2A	USB Type-C, 5V/2A; cable supports data transfer	USB Type-C, 5V/2A
Included cartridges	0.6Ω pre-installed and 0.8Ω spare	Stainless-steel 0.6Ω and 0.8Ω	0.6Ω pre-installed and 0.8Ω spare
Size	114.5 × 25.0 × 15.0mm	114.5 × 25.0 × 15.0mm	119.9 × 25.7 × 15.0mm
Weight	67g	67g	77.4g
Materials	Zinc alloy with artificial leather or IML panel, PCTG cartridge	Zinc alloy with carbon fibre or IML panel, PCTG cartridge	Zinc alloy and PCTG

Shared by all: 5-30W output, 2ml (TPD) XLIM Top Fill cartridges in 0.4Ω, 0.6Ω, 0.8Ω and 1.2Ω, side airflow control, USB Type-C charging at 5V/2A, and both auto-draw and fire-button activation.

Comparison facts were checked against current product packaging and manufacturer information, last checked 2026-08-01. Where sources differed, evidence for the current Vape Offers SKU took priority. Each model's price and availability are shown live from its own product record.

Add your own e-liquid

E-liquid: what to use & where to buy

Nothing arrives pre-filled, so e-liquid is bought separately and the right one depends on the cartridge you fit.

The 0.8 ohm cartridge supplied with the kit is paired by OXVA with nicotine salts, and the 0.6 ohm takes freebase or salt. As a rule the tighter, cooler resistances suit higher-strength salts, and the warmer more open ones suit lower strengths.

Thick high-VG shortfills are the one thing to avoid. A mesh coil this small cannot wick liquid that heavy fast enough, and the result is a dry hit rather than a bigger cloud.

Verified resistance-specific guidance, where available, is shown with each pod in the compatibility section above. Ready to stock up?

Is this right for you?

Prefilled pods vs. the full kit

This is the kit: the XLIM Pro device itself, supplied with two cartridges so you can start straight away. If you already own an XLIM Pro and just need cartridges, buy those on their own instead - you do not need a second device.

E-liquid is separate either way. This is a refillable system, so nothing arrives pre-filled.

OXVA lists the XLIM Pro as taking the XLIM Top Fill cartridge, the V3 cartridges in 0.4, 0.6, 0.8 and 1.2 ohm, the older V2 cartridges in 0.6, 0.8 and 1.2 ohm, and OXVA's prefilled cartridges.

There is one documented exception, and OXVA states it plainly on their own specification: the XLIM C cartridge does not fit. The XLIM C is a separate platform with its own cartridges despite sharing the XLIM name.

NeXLIM cartridges are a different platform again and are not compatible either.

Before you order

What is in the kit?

1 × OXVA XLIM Pro 3 device
1 × XLIM Top Fill 0.6Ω cartridge, pre-installed
1 × XLIM Top Fill 0.8Ω cartridge
1 × USB Type-C cable
1 × user manual, use suggestion card and button operation guide

Cartridges are the 2ml UK version. A lanyard is not listed in the Pro 3 pack. E-liquid is not included.

The basics

How it works

The XLIM Pro runs a 1000mAh battery at 5-30W and fires either on the button or by drawing on it, whichever you prefer. Airflow is set with a slider on the side of the device rather than by twisting the cartridge, so once you find your draw it stays put.

The cartridge carries the coil, so the resistance you fit is what decides the experience. OXVA publishes a wattage band for each one: 0.4 ohm at 26-30W, 0.6 ohm at 20-25W, 0.8 ohm at 12-16W and 1.2 ohm at 10-12W. The two supplied with the kit are 0.6 and 0.8 ohm, which between them cover most of the range from a warmer restricted draw to a tighter mouth-to-lung one.

Charging is over USB-C at 5V/2A.

Get started

Setup & how to use

Take the cartridge out, lift the silicone stopper on the top edge and fill slowly, leaving a small air gap rather than filling to the brim. Close the stopper firmly and seat the cartridge back in the device.

Leave a freshly filled cartridge to stand for a few minutes before the first draw, and take two or three pulls without firing to help the coil wick. This is the step most people skip, and it is the reason a brand-new cartridge can taste burnt on day one.

Set the wattage inside OXVA's band for the resistance you fitted, starting at the lower end, and open or close the side airflow slider until the draw feels right.

If something is not right

Troubleshooting

A burnt taste on a new cartridge almost always means it was fired before the wick had saturated, or that the wattage is set above OXVA's band for that resistance. Neither can be undone once the cotton has scorched, so it is worth getting right first time.

No fire or weak output is usually the contacts rather than the device. Remove the cartridge, wipe the contacts on both the cartridge and inside the device with a dry tissue, and reseat it firmly.

Gurgling or liquid in the mouthpiece points to overfilling or a stopper that has not been pressed fully shut. Very thick high-VG e-liquid can flood these coils for the same reason.

If the device will not charge, try a different USB-C cable before assuming a fault - the port collects pocket lint and a dry cocktail stick clears it.

Verified product facts

Specifications

Product type: Refillable pod kit
Battery capacity: 1500mAh built in
Output range: 5–30W
Charging: USB Type-C, 5V/2A
Display: 1.05-inch colour screen
Chipset: OXVA Photon chip with Pulse output system
Airflow: Side airflow control
Activation: Auto-draw or fire button
UK cartridge capacity: 2ml
Included cartridges: 0.6Ω pre-installed and 0.8Ω spare
Compatible resistances: 0.4Ω, 0.6Ω, 0.8Ω and 1.2Ω
Compatible cartridges: XLIM Top Fill cartridge family
Dimensions: 119.9 × 25.7 × 15.0mm
Weight: 77.4g
Materials: Zinc alloy and PCTG
Charging cable included: Yes; standard USB Type-C cable

Use it safely

Safety, storage & recycling

Keep the device and its built-in battery away from extreme heat, water and direct sunlight. Charge on a non-flammable surface using a USB-C lead and don't leave it charging unattended. Keep the device, pods and e-liquid out of reach of children and pets, and wash your hands after handling e-liquid.

At end of life, don't put the device in general waste — recycle it at a battery or small-electricals recycling point, or via a vape take-back scheme where available. Empty pods can be recycled with small electricals where accepted.

Helpful answers

Frequently asked questions

What does the Pro 3 add over the Pro 2?

A larger 1500mAh battery against 1300mAh, and a 1.05-inch colour screen in place of the 0.56-inch one. It also runs OXVA's newer Photon chip with its Pulse output system.

Output is unchanged at 5-30W, and it takes the same XLIM Top Fill cartridges, so nothing you already own is stranded.

OXVA lists a 3ml cartridge - why is mine 2ml?

OXVA publishes the Pro 3 cartridge as 3ml with a 2ml TPD version. UK law caps a refillable pod at 2ml, so the cartridges sold here are the 2ml version.

Coil, resistances and fill method are otherwise identical.

How fast does the Pro 3 charge?

OXVA publishes the charging spec as USB Type-C at 5V/2A. Its marketing also quotes 80% in 30 minutes, but OXVA does not publish a higher charge current to support that, so treat the time as indicative rather than a specification.

Which cartridges does the Pro 3 take?

XLIM Top Fill cartridges in 0.4Ω, 0.6Ω, 0.8Ω and 1.2Ω. The kit comes with 0.6Ω fitted and a 0.8Ω spare.

NeXLIM cartridges do not fit - that is a separate OXVA platform.

Editorial standards

How we verified this product

Vape Offers checked the battery, 5-30W range, 1.05-inch screen, charge rate, cartridge resistances, dimensions, weight, materials and pack contents against OXVA's published XLIM Pro 3 specification, accessed 1 August 2026. OXVA's 80%-in-30-minutes claim is not supported by any published charge current above 5V/2A, so it is treated as indicative rather than a specification.

OXVA XLIM Pro 3 Pod Kit

Compatible replacement pods & resistances